Home › Concrete Calculator › This size
How Much Concrete for a 12×12 Slab at 4 Inches?
A 12 ft × 12 ft slab, 4 inches thick, needs 1.78 yd³ net — with a 10% waste allowance that is 1.96 yd³, so you order 2.00 yd³ of ready-mix. That is about 88 bags of 80 lb mix, 118 of 60 lb, or 176 of 40 lb. It weighs roughly 7,822 lb (3.9 tons) and costs about $528 in bags or $430 delivered as ready-mix. Change anything below and the figures follow.
Answer: 2 cubic yards
How many bags of concrete for a 12×12 slab?
| Bag size | Bags needed | Yields | Weight to handle |
|---|---|---|---|
| 80 lb | 88 bags | 0.60 ft³ each | 7,040 lb |
| 60 lb | 118 bags | 0.45 ft³ each | 7,080 lb |
| 40 lb | 176 bags | 0.30 ft³ each | 7,040 lb |
All three rows buy the same 1.96 yd³ with 10% waste included (net was 1.78 yd³). Smaller bags mean more of them to open, but they are easier to lift and easier to mix in small batches.
These are genuinely mixable by hand. Budget two to three minutes per bag in a drum mixer, so the mixing alone is around 4.4 hours before anyone starts screeding — which is why this size usually gets two or three people and a hired mixer rather than one wheelbarrow. Mix only what you can place within about 20 minutes, and keep the batches consistent: too much water in one batch is what leaves a dusty, weak patch in an otherwise sound slab.
If your slab is a different size
Same 4 inch thickness, same 10% waste allowance, different footprint:
| Size | Order at 4 in |
|---|---|
| 10×10 | 1.50 yd³ · 62 bags |
| 10×12 | 1.75 yd³ · 74 bags |
| 12×16 | 2.75 yd³ · 118 bags |
| 10×20 | 2.75 yd³ · 123 bags |
| 16×16 | 3.50 yd³ · 157 bags |
How it changes with thickness
Same area, different thickness:
| Thickness | 4 | 5 | 6 |
|---|---|---|---|
| Order this much | 2 cubic yards | 2.50 cubic yards | 3 cubic yards |
| With 10% waste | 1.96 yd³ | 2.44 yd³ | 2.93 yd³ |
What a 12×12 slab at 4 inches actually involves
This is the awkward middle: too big to enjoy mixing by hand — 88 bags is roughly 3.9 tons to carry and open — but small enough that a ready-mix supplier will add a short-load surcharge for sending a truck. Most people at this size either hire a drum mixer and do it in a day with three or four people, or pay the surcharge and take the easy route. Decide before you order, because you cannot change your mind halfway through a pour.
The slab is 144 ft² and, at 4 inches thick, needs 48.00 ft³ net (1.78 yd³). With a 10% waste allowance that is 52.80 ft³ (1.96 yd³), so you order 2.00 yd³ of ready-mix after the usual 1/4-yard round-up. That load weighs about 3.9 tons. Everything below is worked out from those figures.
Full material list
| Item | Quantity | Notes |
|---|---|---|
| Concrete (order) | 2.00 yd³ | 10% waste included; 88 × 80 lb bags, or 118 × 60 lb bags |
| Gravel base | 2.13 yd³ | order loose for 4 in compacted; see the gravel calculator |
| Form lumber | 53 lin ft | 2×4 or 2×6, includes 10% waste |
| Form stakes | 12 | roughly one every 4 ft of perimeter |
| Welded wire mesh | 4 sheets | 5×10 ft sheets of 6×6-W1.4 mesh, 10% overlap |
| Vapor barrier | 158 ft² | about 16 lin ft of 10 ft wide roll |
| Control joints | 2 joints | 24 lin ft of saw cut |
Control joints and cracking
Control joints stop a slab cracking wherever it likes. The conservative rule is to space them at twice the slab thickness in inches — here that means every 8 ft, which divides this slab into 2 × 2 panels of roughly 6.0 × 6.0 ft. That is 2 joints, about 24 linear ft of cutting. Get them in while the concrete is still green, typically 6 to 12 hours after finishing, before random cracks get there first.
Reinforcement at 4 inches
At 4 in, 4 sheets of 6×6-W1.4 welded wire mesh on chairs is the standard reinforcement. Lap the sheets about 6 in and keep them at mid-depth, so the steel ends up in the middle of the slab rather than resting on the sub-base. Mesh does not stop cracks forming — it holds them tight after they do, which is exactly what you want in a patio or shed floor. If this slab will take vehicles, step up to 5 or 6 in and use rebar instead.
Bagged concrete or a ready-mix truck?
| Option | Quantity | Estimated cost |
|---|---|---|
| Bagged 80 lb | 88 bags | $528 |
| Ready-mix delivered | 2.00 yd³ + short-load fee | $430 |
On these assumptions ready-mix is cheaper ($430 vs $528) as well as far less work. It only wins if the truck can actually reach the site and you can place the whole load without stopping. If access is a problem, bagged at $528 is the practical fallback and lets you pour in stages.
Costs assume $6 per 80 lb bag, $170 per cubic yard delivered, and a $90 short-load surcharge below 5 yd³. Ready-mix pricing moves with region, season and fuel, so treat these as a starting point for calling suppliers rather than a quote.
Pour day, in order
- Excavate to 8 in below finished grade: 4 in of slab plus 4 in of base.
- Spread the base in two lifts and compact each one. Rent a plate compactor; a hand tamper leaves soft spots that crack later.
- Set the forms to 4 in, level and square, staked every 4 ft.
- Lay the vapor barrier with 6 in laps, then the mesh on chairs so it ends up mid-depth rather than resting on the ground.
- Set up the mixing station before you open a bag: water, hose, wheelbarrow or drum mixer, and a place to dump. Mix only what you can place within about 20 minutes.
- Place, screed and float in one continuous run. A batch that sits while you fetch something is a batch you will be fighting later.
- Cut or tool the control joints while the concrete is still green, aiming for 6 to 12 hours after finishing. You need about 24 linear ft of cutting.
- Cover it and keep it damp for 7 days. Full design strength arrives at 28 days.
Local codes cover frost depth, reinforcement and permits, and they vary from place to place. Check with your local building department before you dig or pour.
Common questions
How many bags of concrete do I need for a 12×12 slab?
88 bags of 80 lb mix, 118 of 60 lb, or 176 of 40 lb, all at 4 inches thick with a 10% waste allowance. Net volume is 48.00 ft³ (1.78 yd³); with waste that is 52.80 ft³ (1.96 yd³), so you order 2.00 yd³ of ready-mix. Divide the with-waste volume by the yield on the bag — 0.60 ft³ for an 80 lb bag — then round up.
How much does a 12×12 slab weigh?
About 7,822 lb, or 3.9 tons including the 10% waste allowance. Concrete runs roughly 4,000 lb per cubic yard and the with-waste volume is 1.96 yd³. That weight matters twice: on the sub-base you are pouring onto, and on whatever vehicle fetches the material.
How much does a 12×12 concrete slab cost?
Roughly $528 in 80 lb bags, or about $430 delivered as ready-mix, which includes a short-load surcharge because the order is under 5 cubic yards (both include 10% waste). Material only — excavation, base, reinforcement and labour are extra. Ring two suppliers; delivered prices move a lot by region.
Can I mix a 12×12 slab myself?
Yes. At 1.96 yd³ with waste this is a one-day job for two people with a rented drum mixer: 88 bags, about 4.4 hours of mixing, then placing, screeding and floating straight after. Stage everything before you open the first bag.
How thick should a 12×12 slab be?
Four inches for a patio, shed base or footpath; five to six inches where a car parks. This page is calculated at 4 inches, and the calculator above re-runs instantly if you switch it — doubling the thickness roughly doubles both the concrete and the cost.
Do I need rebar or mesh in a 12×12 slab?
At 4 inches, 6×6-W1.4 welded wire mesh on chairs is standard. Mesh will not stop a crack forming, but it holds the two sides together when one does, which is what you want in a patio. Step up to rebar if vehicles will drive on it.
Other sizes
- How Much Concrete for a 10×10 Slab at 4 Inches?
- How Much Concrete for a 10×10 Slab at 6 Inches?
- How Much Concrete for a 12×12 Slab at 6 Inches?
- How Much Concrete for a 10×12 Slab at 4 Inches?
- How Much Concrete for a 10×12 Slab at 6 Inches?
- How Much Concrete for a 12×16 Slab at 4 Inches?
- How Much Concrete for a 12×16 Slab at 6 Inches?
- How Much Concrete for a 16×16 Slab at 4 Inches?
- How Much Concrete for a 16×16 Slab at 6 Inches?
- How Much Concrete for a 20×20 Slab at 4 Inches?