MaterialCalc

Home › Concrete Calculator › This size

How Much Concrete for a 10×20 Slab at 4 Inches?

A 10 ft × 20 ft slab, 4 inches thick, needs 2.47 yd³ net — with a 10% waste allowance that is 2.72 yd³, so you order 2.75 yd³ of ready-mix. That is about 123 bags of 80 lb mix, 163 of 60 lb, or 245 of 40 lb. It weighs roughly 10,864 lb (5.4 tons) and costs about $738 in bags or $558 delivered as ready-mix. Change anything below and the figures follow.

Answer: 2.75 cubic yards

How many bags of concrete for a 10×20 slab?

Bag sizeBags neededYieldsWeight to handle
80 lb123 bags0.60 ft³ each9,840 lb
60 lb163 bags0.45 ft³ each9,780 lb
40 lb245 bags0.30 ft³ each9,800 lb

All three rows buy the same 2.72 yd³ with 10% waste included (net was 2.47 yd³). Smaller bags mean more of them to open, but they are easier to lift and easier to mix in small batches.

Read that bag count as a warning rather than a plan. 123 bags is roughly 5.4 tons to carry, open and mix, and the mixing would not finish anywhere near a placement window — a load this size stiffens while you are still working through the pallet. Order ready-mix. The bag figure is here so you can see why: a truck brings the whole 2.75 yd³ in one delivery for about $558.

If your slab is a different size

Same 4 inch thickness, same 10% waste allowance, different footprint:

SizeOrder at 4 in
10×121.75 yd³ · 74 bags
12×122.00 yd³ · 88 bags
12×162.75 yd³ · 118 bags
16×163.50 yd³ · 157 bags
12×244.00 yd³ · 176 bags

How it changes with thickness

Same area, different thickness:

Thickness456
Order this much2.75 cubic yards3.50 cubic yards4.25 cubic yards
With 10% waste2.72 yd³3.40 yd³4.07 yd³

What a 10×20 slab at 4 inches actually involves

This is the awkward middle: too big to enjoy mixing by hand — 123 bags is roughly 5.4 tons to carry and open — but small enough that a ready-mix supplier will add a short-load surcharge for sending a truck. Most people at this size either hire a drum mixer and do it in a day with three or four people, or pay the surcharge and take the easy route. Decide before you order, because you cannot change your mind halfway through a pour.

The slab is 200 ft² and, at 4 inches thick, needs 66.67 ft³ net (2.47 yd³). With a 10% waste allowance that is 73.33 ft³ (2.72 yd³), so you order 2.75 yd³ of ready-mix after the usual 1/4-yard round-up. That load weighs about 5.4 tons. Everything below is worked out from those figures.

Full material list

ItemQuantityNotes
Concrete (order)2.75 yd³10% waste included; 123 × 80 lb bags, or 163 × 60 lb bags
Gravel base2.96 yd³order loose for 4 in compacted; see the gravel calculator
Form lumber66 lin ft2×4 or 2×6, includes 10% waste
Form stakes15roughly one every 4 ft of perimeter
Welded wire mesh5 sheets5×10 ft sheets of 6×6-W1.4 mesh, 10% overlap
Vapor barrier220 ft²about 23 lin ft of 10 ft wide roll
Control joints3 joints40 lin ft of saw cut

Control joints and cracking

Control joints stop a slab cracking wherever it likes. The conservative rule is to space them at twice the slab thickness in inches — here that means every 8 ft, which divides this slab into 2 × 3 panels of roughly 5.0 × 6.7 ft. That is 3 joints, about 40 linear ft of cutting. Get them in while the concrete is still green, typically 6 to 12 hours after finishing, before random cracks get there first.

Reinforcement at 4 inches

At 4 in, 5 sheets of 6×6-W1.4 welded wire mesh on chairs is the standard reinforcement. Lap the sheets about 6 in and keep them at mid-depth, so the steel ends up in the middle of the slab rather than resting on the sub-base. Mesh does not stop cracks forming — it holds them tight after they do, which is exactly what you want in a patio or shed floor. If this slab will take vehicles, step up to 5 or 6 in and use rebar instead.

Bagged concrete or a ready-mix truck?

OptionQuantityEstimated cost
Bagged 80 lb123 bags$738
Ready-mix delivered2.75 yd³ + short-load fee$558

On these assumptions ready-mix is cheaper ($558 vs $738) as well as far less work. It only wins if the truck can actually reach the site and you can place the whole load without stopping. If access is a problem, bagged at $738 is the practical fallback and lets you pour in stages.

Costs assume $6 per 80 lb bag, $170 per cubic yard delivered, and a $90 short-load surcharge below 5 yd³. Ready-mix pricing moves with region, season and fuel, so treat these as a starting point for calling suppliers rather than a quote.

Pour day, in order

  1. Excavate to 8 in below finished grade: 4 in of slab plus 4 in of base.
  2. Spread the base in two lifts and compact each one. Rent a plate compactor; a hand tamper leaves soft spots that crack later.
  3. Set the forms to 4 in, level and square, staked every 4 ft.
  4. Lay the vapor barrier with 6 in laps, then the mesh on chairs so it ends up mid-depth rather than resting on the ground.
  5. Set up the mixing station before you open a bag: water, hose, wheelbarrow or drum mixer, and a place to dump. Mix only what you can place within about 20 minutes.
  6. Place, screed and float in one continuous run. A batch that sits while you fetch something is a batch you will be fighting later.
  7. Cut or tool the control joints while the concrete is still green, aiming for 6 to 12 hours after finishing. You need about 40 linear ft of cutting.
  8. Cover it and keep it damp for 7 days. Full design strength arrives at 28 days.

Local codes cover frost depth, reinforcement and permits, and they vary from place to place. Check with your local building department before you dig or pour.

Common questions

How many bags of concrete do I need for a 10×20 slab?

123 bags of 80 lb mix, 163 of 60 lb, or 245 of 40 lb, all at 4 inches thick with a 10% waste allowance. Net volume is 66.67 ft³ (2.47 yd³); with waste that is 73.33 ft³ (2.72 yd³), so you order 2.75 yd³ of ready-mix. Divide the with-waste volume by the yield on the bag — 0.60 ft³ for an 80 lb bag — then round up.

How much does a 10×20 slab weigh?

About 10,864 lb, or 5.4 tons including the 10% waste allowance. Concrete runs roughly 4,000 lb per cubic yard and the with-waste volume is 2.72 yd³. That weight matters twice: on the sub-base you are pouring onto, and on whatever vehicle fetches the material.

How much does a 10×20 concrete slab cost?

Roughly $738 in 80 lb bags, or about $558 delivered as ready-mix, which includes a short-load surcharge because the order is under 5 cubic yards (both include 10% waste). Material only — excavation, base, reinforcement and labour are extra. Ring two suppliers; delivered prices move a lot by region.

Can I mix a 10×20 slab myself?

Not realistically. 123 bags would have to be mixed and placed faster than a small crew can manage, and a part-set batch cannot be rescued. This is a ready-mix job — about $558 delivered for 2.75 yd³.

How thick should a 10×20 slab be?

Four inches for a patio, shed base or footpath; five to six inches where a car parks. This page is calculated at 4 inches, and the calculator above re-runs instantly if you switch it — doubling the thickness roughly doubles both the concrete and the cost.

Do I need rebar or mesh in a 10×20 slab?

At 4 inches, 6×6-W1.4 welded wire mesh on chairs is standard. Mesh will not stop a crack forming, but it holds the two sides together when one does, which is what you want in a patio. Step up to rebar if vehicles will drive on it.

Other sizes