Home › Drywall Calculator › This size

How Many Sheets of Drywall for a 14×16 ft Room with an 8 ft Ceiling?

A 14 by 16 foot room with an 8 foot ceiling needs this many 4×8 drywall sheets, with mud, tape and screws worked out. Here is the answer, plus a calculator you can adjust if your measurements are slightly different.

Answer: 15 sheets

How it changes with ceiling height

Same area, different ceiling height:

Ceiling height	8	9	10
Drywall sheets needed	15 sheets	17 sheets	19 sheets
Gross wall area	480 ft²	540 ft²	600 ft²

What a 14×16 ft room with an 8 ft ceiling actually involves

At 429 ft² this is a solid two-person job. 15 sheets at 4 ft × 8 ft weigh roughly 825 lb in total, and a full sheet is awkward for one person on a ceiling or above shoulder height. Budget two days: hang on the first, tape and coat on the second.

The room has 60 ft of wall around 480 ft² of gross surface. Knock off 51 ft² for openings and you are boarding 429 ft², or 472 ft² once your 10 percent waste allowance is added. That is 15 sheets of 4 ft × 8 ft board.

Deducting 1 door and 2 windows removes 51 ft², or 11 percent of the wall. That is about 2 sheets you do not buy. Cutting openings out of a hung sheet wastes the offcut, which is exactly what the waste allowance in this calculator is for — do not set it to zero and expect the cuts to come out even.

An 8 ft ceiling divides exactly by 4, so a 4 ft wide sheet hung horizontally lands two full courses with no rip. That is the cheapest way this room can be boarded: no narrow strips to cut, no extra screws along a sliver of board, and nothing to fill above your head. Use it.

Where the square footage goes

Measured as	Amount	How it is worked out
Perimeter	60 ft	14 ft + 16 ft, doubled
Gross wall area	480 ft²	60 ft × 8 ft ceiling
Doors deducted	21 ft²	1 × 21 ft²
Windows deducted	30 ft²	2 × 15 ft²
Net area to board	429 ft²	gross minus openings
With 10% waste	472 ft²	the figure to buy against
4 ft × 8 ft sheets	15 sheets	472 ft² ÷ 32
4 ft × 12 ft sheets	10 sheets	472 ft² ÷ 48
Ceiling, if you board it	7 more sheets	14 × 16 = 224 ft², no openings to deduct

At 14 ft × 16 ft you have two 16 ft runs and two 14 ft runs. Board the long walls first and keep the offcuts — they are usually the right length for the short walls, which is where a 20 percent saving on sheet count comes from.

Wall by wall

4 ft × 8 ft sheets hung horizontally, at an 8 ft ceiling, divide into 2 courses per wall:

Wall run	Surface	Pieces at 4 ft × 8 ft
2 × 14 ft wall	224 ft²	2 sheets per course × 2 = 4 per wall, 8 in total
2 × 16 ft wall	256 ft²	2 sheets per course × 2 = 4 per wall, 8 in total

Those are pieces, not sheets. Laid out literally the walls would take 16 pieces, against the 15 sheets you actually buy — the gap is the 0 ft offcut that comes off every 16 ft run and finishes the next course. It is the biggest saving available on a room this size, and it only works if you cut the long walls first and keep the offcuts.

At 16 ft by 14 ft the room is close to square, and this is the shape where the cutting sequence matters most. Every run leaves a 0 ft piece over, and that same piece is exactly what the next course needs — so cut the first sheet of each course down to the run length and start the next course with the offcut. Cut every course from a fresh sheet instead and you will buy three or four sheets you never needed.

A 16 ft run takes 2 sheets per course and leaves 0 ft of offcut every time. The 16 ft runs take 2 each and leave 0 ft — which is the piece that usually finishes the ends without touching another full sheet.

Mud, tape and screws

Item	Quantity	Rule of thumb
Joint compound	2 gal	about 1 gal per 300 ft² for a level 4 finish
Joint tape	1 roll	a 500 ft roll per 500 ft² of board
Drywall screws	520	about 1.1 per ft², roughly 32 per 4×8 sheet
Studs, if reframing	55	1 per ft at 16 in centres, plus 4 for corners and 2 per opening
Corner bead	as needed	one length per outside corner, inside and outside

Buy the mud in the largest tub that stays workable. A 2 gal job is 1 standard 4.5 gal bucket, and once a bucket is opened it skins over within days — powder you mix yourself keeps indefinitely and is cheaper per gallon on a job this size. Coat thin and build up: three thin passes sand far easier than two thick ones, and every extra pass costs you sanding time, not just mud.

How to hang it

Mark and check the studs. Board goes across them, so it does not matter if the spacing wanders — but it does matter that you can find them after the board is up.
Start at the top with a full 4 ft course, then a second full course below it.
Stagger the vertical joints. A joint that lines up with the one on the other side of a stud is the one that cracks first.
Keep the board about 1/2 in off a concrete floor and tight to the ceiling. Movement happens at the floor line, not at the ceiling.
Screw about 12 in apart in the field and every 8 in on the edges, driving the heads just below the surface without breaking the paper. A screw that tears the paper holds nothing.
Leave a 1/8 in gap at butt joints and fill it with mud before taping. Boards that are jammed tight buckle at the seam.
This room needs 15 sheets and roughly 520 screws. Order the sheets and the screws together — a shortfall of 20 screws is a wasted trip.

Which board to buy

1/2 in board is the default for walls and is what the count above assumes. Step up to 5/8 in for ceilings and for bedrooms where you want the room to feel quieter; it sags less at 24 in centres and takes screws better, at about 20 percent more weight per sheet. Use 1/4 in only for curves. For bathrooms, laundry rooms and basements use moisture-resistant board — it is not waterproof, and it still needs a proper waterproofing layer behind a tiled shower. Board that is going to sit in a garage or a shed is worth buying in 5/8 in for the impact resistance alone.

Common questions

How many sheets of drywall for a 14×16 ft room with an 8 ft ceiling?

15 sheets of 4 ft × 8 ft board, or 10 if you buy 4 ft × 12 ft sheets. The walls come to 429 ft² after deducting 1 door and 2 windows, and 472 ft² with your 10 percent waste allowance.

Do I need to add the ceiling?

Only if you are boarding it. The ceiling here is 224 ft², which is 7 more 4 ft × 8 ft sheets, roughly 52 percent on top of the walls. Ceilings take longer per sheet than walls — everything is overhead — so treat it as separate work, not extra work.

How do I hang drywall on an 8 ft ceiling?

An 8 ft wall divides into two 4 ft courses with no rip, so hang two full-width courses. Board horizontally across the studs and stagger the vertical joints.

How much joint compound and how many screws?

About 2 gallons of compound and 520 screws for this room, plus 1 roll of tape. Buy a little more mud than the figure: a second coat always drinks more than the first, and running out mid-pass leaves a ridge you have to sand flat.

Should I hang drywall horizontally or vertically?

Horizontally, across the studs, unless you are using 4 ft × 12 ft sheets at an 8 ft ceiling. Horizontal hanging puts fewer joints in the middle of the wall, and every joint you can put at a height you can reach is a joint that is easier to finish. Vertical hanging is faster to put up and harder to finish.